High Performance Pipe Fitting Stainless Steel Pipe Joint - 310S stainless steel coil – Cepheus

Product Detail

Stainless Steel coil

Stainless steel coil can be made by hot rolling and cold rolling, including the thickness of 0.31-3.0 mm sheet and 3.0-30 mm plate. Hot-rolled stainless steel is not as good as cold-rolled in mechanical properties, but there are good toughness and ductility. Cold-rolled stainless steel plate is low in toughness due to the good hardening. In order to ensure all kinds of stainless steel yield strength, tensile strength, elongation and hardness and other mechanical properties to meet the requirements, prior to delivery must be stainless steel annealing, solution treatment, aging heat treatment.

Material Grade

Material	ASTM A240 Standard	201, 304 304L 304H 309S 309H 310S 310H 316 316H 316L 316Ti 317 317L 321 321H 347 347H 409 410 410S 430 904L
	ASTM A480 Standard	302, s30215, s30452, s30615, 308, 309, 309Cb, 310, 310Cb, S32615,S33228, S38100, 304H, 309H, 310H, 316H, 309HCb, 310HCb, 321H,347H, 348H, S31060, N08811, N08020, N08367, N08810, N08904,N08926, S31277, S20161, S30600, S30601, S31254, S31266,S32050, S32654, S32053, S31727, S33228, S34565, S35315,S31200, S31803, S32001, S32550, S31260, S32003, S32101,S32205, S32304, S32506, S32520, S32750, S32760, S32900, S32906, S32950, S32974
	JIS 4304-2005 Standard	SUS301L,SUS301J1,SUS302,SUS304, SUS304L, SUS316/316L, SUS309S, SUS310S, 3SUS21L, SUS347, SUS410L, SUS430, SUS630
	JIS G4305 Standard	SUS301, SUS301L, SUS301J1, SUS302B, SUS304, SUS304Cu,SUS304L, SUS304N1, SUS304N2, SUS304LN, SUS304J1, SUSJ2,SUS305, SUS309S, SUS310S, SUS312L, SUS315J1, SUS315J2,SUS316, SUS316L, SUS316N, SUS316LN, SUS316Ti, SUS316J1,SUS316J1L,SUS317, SUS317L, SUS317LN, SUS317J1, SUS317J2,SUS836L, SUS890L, SUS321, SUS347, SUSXM7, SUSXM15J1, SUS329J1, SUS329J3L, SUS329J4L, SUS405, SUS410L, SUS429, SUS430, SUS430LX, SUS430J1L, SUS434, SUS436L, SUS436J1L,SUS444, SUS445J1, SUS445J2, SUS447J1, SUSXM27, SUS403,SUS410, SUS410S, SUS420J1, SUS420J2, SUS440A

Product Specification

Finish	Thickness	Characteristics	Applications
No. 1	3.0mm~50.0mm	Finished by hot-rolling, annealing and pickling, characterized by white pickled surface	Chemical industry equipment, Industrial tanks
No. 2B	0.3mm~6.0mm	Finished by heat treatment, pickling after cold rolling, followed by skin pass line to be more brighter and smooth surface	General Application Medical Instruments, Tableware
No. BA (Bright Annealed)	0.5mm~2.0mm	Bright heat treatment after cold rolling	Kitchen utensil, kitchen ware, architectural purpose
No. 4	0.4mm~3.0mm	Polishing with No. 150 to No.180 mesh abrasives. The most popular finishes	Milk & Food processing facilities, Hospital Equipment, Bath-tub
No. 8	0.5mm~2.0mm	A mirror-like reflective surface by polishing with finer abrasives over 800 mesh	Reflector, Mirror, Interior-Exterior decoration forbuilding
HL(Hair Line)	0.4mm~3.0mm	Finished by continuous linear polishing	Architectural purposes, escalators, kitchen ware vehicles

Standard sizes

Size	Thickness: 0.15mm-3.00mm (Cold Rolled sheets); 4-30mm (Hot rolled plate)
	Width:1000mm, 1219mm, 1250mm, 1500mm, 1800mm, 2000mm
	Length: as coils

Chemical composition

Grade	C	Si	Mn	P	S	Cr	Ni	Mo	Ti	N	Cu	Nb
201	≤0.15	≤1.0	5.50-7.50	≤0.05	≤0.03	16.00-18.00	3.50-5.50	-	-	0.05-0.25	-	-
202	≤0.15	≤1.0	7.50-10.00	≤0.05	≤0.03	17.00-19.00	4.00-6.00	-	-	0.05-0.25	-	-
301	≤0.15	≤1.0	≤2.0	≤0.045	≤0.03	16.00-18.00	6.00-8.00	-	-	≤0.1	-	-
302	≤0.15	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	8.00-10.00	-	-	≤0.1	-	-
303	≤0.15	≤1.0	≤2.0	≤0.2	≥0.15	17.00-19.00	8.00-10.00	≤0.6	-	≤0.1	-	-
304	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	8.00-10.00	-	-	-	-	-
304L	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	8.00-10.00	-	-	-	-	-
304H	0.04-0.1	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	8.00-10.00	-	-	-	-	-
304N	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	8.00-10.00	-	-	0.10-0.16	-	-
304J1	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	6.00-9.00	-	-	-	1.00-3.00	-
305	≤0.12	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	10.50-13.00	-	-	-	-	-
309S	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	22.00-24.00	12.00-15.00	-	-	-	-	-
310S	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	24.00-26.00	19.00-22.00	-	-	-	-	-
316	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	10.00-14.00	2.00-3.00	-	-	-	-
316L	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	12.00-15.00	2.00-3.00	-	-	-	-
316H	≤0.1	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	10.00-14.00	2.00-3.00	-	-	-	-
316N	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	16.00-18.00	10.00-14.00	2.00-3.00	-	0.10-0.16	-	-
316Ti	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	16.00-19.00	11.00-14.00	2.00-3.00	≥5C	-	-	-
317L	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	18.00-20.00	11.00-15.00	3.00-4.00	-	-	-	-
321	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	9.00-12.00	-	5C-0.7	-	-	-
347	≤0.08	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	9.00-12.00	-	-	-	-	10C-1.10
347H	≤0.1	≤1.0	≤2.0	≤0.035	≤0.03	17.00-19.00	9.00-12.00	-	-	-	-	8C-1.10
2205	≤0.03	≤1.0	≤2.0	≤0.035	≤0.03	21.00-24.00	4.50-6.50	2.50-3.50	-	0.08-0.20	-	-
2507	≤0.03	≤0.8	≤1.2	≤0.035	≤0.02	24.00-26.00	6.00-8.00	3.00-5.00	-	0.24-0.32	-	-
904L	≤0.02	≤1.0	≤2.0	≤0.045	≤0.03	19.00-23.00	23.00-28.00	4.00-5.00	-	-	1.00-2.00	-
C276	≤0.02	≤0.05	≤1.0	-	-	14.00-16.50	Other	-	-	-	-	-
Monel400	≤0.3	≤0.5	≤2.0	-	≤0.024	-	≥63	-	-	-	28-34	-
409L	≤0.03	≤1.0	≤1.0	≤0.035	≤0.03	17.00-19.00	-	-	-	-	-	-
410	≤0.15	≤1.0	≤1.0	≤0.035	≤0.03	11.50-13.50	-	-	-	-	-	-
410L	≤0.03	≤1.0	≤1.0	≤0.035	≤0.03	11.50-13.50	-	-	-	-	-	-
420J1	0.16-0.25	≤1.0	≤1.0	≤0.035	≤0.03	12.00-14.00	-	-	-	-	-	-
420J2	0.26-0.40	≤1.0	≤1.0	≤0.035	≤0.03	12.00-14.00	-	-	-	-	-	-
430	≤0.12	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	-	-	-	-	-
436L	≤0.025	≤1.0	≤1.0	≤0.035	≤0.03	16.00-19.00	-	-	-	-	-	-
439	≤0.03	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	-	-	-	-	-
440A	0.60-0.75	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	≤0.75	-	-	-	-
440B	0.75-0.95	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	≤0.75	-	-	-	-
440C	0.95-1.2	≤1.0	≤1.0	≤0.035	≤0.03	16.00-18.00	-	≤0.75	-	-	-	-
441	≤0.03	0.2-0.8	≤0.7	≤0.03	≤0.015	17.50-18.50	-	≤0.5	0.1-0.5	≤0.025	-	0.3+3C-0.9